Registered Air Tightness Testers – Australia

All members of ATTMA are independently audited and certified, with a scope covering air tightness testing to the ATTMA Technical Standards (TSL1 &/or TSL2) and BS EN:13829 (2001), demonstrating knowledge and understanding, which enables them to test both commercial and domestic developments in accordance with relevant building regulations.

The List of Members is shown below:

EA Calculator Only Authorised to carry out Envelope Area and Volume calculations but is not authorised to test
Level 1 Air tightness tester able to test dwellings and non-dwellings up to 4000m³ gross envelope volume, tested as a single entity with a single blower door fan.
Level 2 Air tightness tester able to test both Level 1 and large buildings up to 80,000m2 external envelope area and/or up to 15 storeys tall. Level 2 testers are able to test buildings defined in Level 1. NOTE – All Level 2 testers are required to have at least one candidate that has the ‘+EA’ level.
Level 3 Testers who have been assessed for a higher level of expertise can test Large, Complicated and High Rise (LCHR), phased and zonal hand-over buildings. Level 3 testers are able to test buildings as defined in Level 1 and 2.
Suspended Testers who have been temporarily removed from the scheme for failure to comply with the scheme rules or companies that have failed to pay the scheme fees. These companies are NOT authorised to test under the ATTMA scheme.
+EA Testers with +EA are competent to carry out envelope area calculations to Level 2 / 3 on behalf of their business. Companies cannot operate at Level 2 or 3 without either an EA Calculator or an engineer with +EA attached to their status.
Provisional Member (International Only) Provisional Members are members that have been desktop audited but have not been physically audited. This only applies to international members where audits cannot always be completed immediately.
CompanyOfficeTesterATTMA No.Level 1Level 2+EA+PHStatus
3ARKVictoria
Ash Mogensen4011Current
3ARK
Victoria
Ratko Mrkogaca
4013
Current
Air Leakage Measurement AustraliaCanberraAndrew Champness4022Current
Air Tightness Testing Services Australia P/LBrisbaneJohn Barrett4012Current
ArupSydneyHan Zhang4021Current
Baw Baw Sustainability NetworkVictoriaMalcolm McKelvie4037Current
Blower Door ServicesLugarnoPeter Shea4010Current
CETECMelbourneAdam Garrys
4017Current
CETECMelbourneAndrew Bellamy
4018Current
CETECMelbourneBen Lindsay4016Current
CETECMelbourneBrooke Maetam
4019Current
CETECMelbourneJosiah Padget
4020Current
CSR Building ProductsSydneyJesse Clarke4014Current
Detail GreenVictoriaLuc Plowman4030Current
Efficiency MatrixVictoriaJohn Konstantakopoulos4002Current
Efficiency MatrixVictoriaJoseph Cheung4003Current
EMSS LtdSydneyMatthew Stephenson1353Current
ENERGYARRESTVictoriaBrian MacSweeney4024Current
LAROS Technologies
CanberraAlistair McGrath-Kerr4027Current
LAROS Technologies

CanberraAndreas Luzzi4026Current
LAROS Technologies
CanberraJames de Salis4028Current
Passive House Construction & Products
TasmaniaJustin O'Connor4023
Current
Passivenous Consulting Pty LtdCanberraBen Elliston4038Current
Passivhaus Perth Pty LtdPerthGillian Joyner4035Current
Pro ClimaGosfordSean Maxwell4001Current
Smart Plus EnterprisePerthDaniel Kress4034
Current
Sustainability HouseEdwardstownJessica Allen4036Current
Sustainability HouseEdwardstownJoshua Mollison4004
Current
Sustainability HouseEdwardstownMark Brigden
4005Current
Sustainability HouseEdwardstownMark Clayton
4006Current
Vining Air P/LMelbourneBen Vining
4008Current
Vining Air P/LMelbourneDaniel O'Malley
4009Current
Vining Air P/LMelbourneNeil Vining
4007Current
Vipac Engineers & ScientistsVictoriaGreg King
4031Current
Vipac Engineers & ScientistsVictoriaJared Carnie
4033Current
Vipac Engineers & ScientistsVictoriaTim Roffey
4032Current

Any queries regarding current membership status should be directed to Barry Cope (ATTMA Scheme Manager) to manager@attma.org.

New date added - 3D modelling for beginners - 22 August 2018 Dismiss